Home  ꄲ  Other Boards  ꄲ  Binocular Camera Base Board Designed for CM4 (Optional Interface Expander)

Binocular Camera Base Board Designed for CM4 (Optional Interface Expander)

Binocular Camera Base Board Designed For Raspberry Pi Compute Module 4, Optional Interface Expander

 

Binocular Camera Base For CM4

Suitable For Evaluating The Raspberry Pi CM4 Or Being Integrated Into End Products

Designed for Compute Module 4 Lite/eMMC variants

 

Connecting With Compute Module 4

Standard CM4 Socket, Compatible With Compute Module 4 Lite/EMMC Variants

Dual Camera Base Introduction

Providing Interfaces Including ETH, HDMI, Micro SD, USB

DUAL CAMERA BASE SPECIFICATIONS
CM4 socket suitable for all variants of Compute Module 4
Networking Gigabit Ethernet RJ45
USB USB 2.0 × 1
FFC connector HDMI & PCIe & USB FFC connector × 1
GPIO FFC connector × 1
Dual camera pixels 8MP
sensor IMX219
resolution 3280 × 2464 (per channel)
CMOS size 1/4 inch
aperture F2.4
focal length 2.6mm
FOV 83/73/50 degree (diagonal/horizontal/vertical)
distortion < 1%
baseline length 60mm
Video HDMI × 1, supports 4K 30fps output
Storage MicroSD card socket for Compute Module 4 Lite (without eMMC) variants
Power input 5V/2.5A
Dimensions 85.0 × 51.5mm

 

Optional Interface Expander Introduction

Providing Interfaces Including GPIO, HDMI, USB, M.2 M KEY

INTERFACE EXPANDER SPECIFICATIONS
USB USB 2.0 × 3
FFC connector HDMI & PCIe & USB FFC connector × 1
GPIO FFC connector × 1
Other connector M.2 M KEY × 1, for connecting NVME SSD or communication module
Raspberry Pi 40PIN GPIO header × 1
Video HDMI × 1, supports 4K 30fps output
Dimensions 85.0 × 51.5mm

 

 

8MP, Clear Imaging, Effective Recognition

Dual 8MP Cameras, Up To 3280 × 2464 Resolution Per Camera

 

Dual 4K UHD Outputs Support

Dual HDMI Ports, Supports Dual 4K 30fps Outputs

Reserved Space For Heatsink

Allows Attaching Heatsink For Better Heat Dissipation

What's On Board

The Dual Camera Base

  1. 1. CM4 socket
    suitable for all variants of Compute Module 4
  2. 2. HDMI connector
    supports 4K 30fps output
  3. 3. USB 2.0 port
    for connecting sorts of USB devices
  4. 4. PWR & USB
    USB-C connector, 5V DC power supply or USB programming port
  5. 5. BOOT selection
    ON: CM4 will be booted from USB-C interface
    OFF: CM4 will be booted from eMMC or Micro SD card

  6. 6. CM4 status indicator
    PWR: Raspberry Pi power indicator
    ACT: Raspberry Pi operating status indicator

  7. 7. RJ45 Gigabit Ethernet
    10/100/1000M compatible
  8. 8. Micro SD card slot
    for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)
  9. 9. GPIO FFC connector
    for expanding 40PIN GPIO
  10. 10. HDMI & PCIe & USB FFC connector
    for expanding HDMI1, PCIe, USB
  11. 11. Dual cameras
    IMX219, 8MP

The Interface Expander

  1. 1. USB 2.0 port
    for connecting sorts of USB devices
  2. 2. HDMI1 connector
    supports 4K 30fps output
  3. 3. HDMI & PCIe & USB FFC connector
    for expanding HDMI1, PCIe, USB
  4. 4. GPIO FFC connector
    for expanding 40PIN GPIO
  5. 5. 40PIN GPIO header
    for connecting sorts of Raspberry Pi HATs
  6. 6. M.2 M KEY
    for NVME SSD, or communication module with PCIE M.2 M KEY interface
  7. 7. M.2 indicator
    indicating operating status of the interface

Outline Dimensions